Engineering (General) Expert Witnesses: 80

Non-testifying consulting support for counsel on matters involving fall protection and access systems, including BMU, suspended, and permanent access systems (U.S. and International)

Rauch Safety & Engineering provides non-testifying technical consulting to counsel in matters involving fall protection systems, façade access systems (including Building Maintenance Units – BMUs), and permanent access infrastructure.

Engagements are typically initiated prior to expert designation to evaluate the technical validity of a claim, defense, or opposing position. This allows counsel to determine whether a matter is structurally sound before proceeding into formal expert pathways.

Work focuses on system failures, installation alignment, and responsibility across design, manufacturing, and construction, particularly where breakdowns occur between design intent and real-world conditions.

Scope includes analysis of:

• System design and engineering intent 
• Installation and commissioning conditions
• Lifecycle use and maintenance environments
• Alignment with applicable standards (OSHA, ANSI, IWCA)

RSE is engaged to:

• Evaluate case feasibility and technical merit
• Identify system failures, misalignment, and responsibility gaps
• Analyze construction defects and performance issues
• Review and assess opposing expert reports 
• Determine design vs. installation discrepancies 

RSE operates independently of contractors, manufacturers, and installers, providing unbiased technical evaluation grounded in real-world system behavior across the full system lifecycle.

All engagements are strictly non-testifying and available across U.S. and international matters.

Key Services

• Early Case Technical Evaluation (Fall Protection & Access Systems)
• Construction Defect & System Performance Analysis (Fall Protection & Access Systems)
• Failure Analysis – Fall Protection & Access Systems
• BMU / Façade Access System Review
• Suspended Access & Permanent Access System Evaluation
• Commissioning & Installation Condition Review (Fall Protection & Access Systems)
• Lifecycle & Maintenance Condition Assessment (Fall Protection & Access Systems)
• OSHA / ANSI / IWCA Standards Interpretation (as applicable to Fall Protection & Access Systems)
• Expert Report Review & Rebuttal Support (Non-testifying, Fall Protection & Access Systems)
• Design vs. Installation Discrepancy Analysis (Fall Protection & Access Systems)

Positioning Statement

RSE provides non-testifying consulting support to counsel requiring a clear, technically grounded understanding of fall protection and access systems and their real-world performance, particularly in matters where design, manufacturing, installation, and operational realities intersect.

Areas of Expertise:

Fall Protection Systems Failure Façade Access Systems Failure Building Maintenance Units (BMU) Failure Suspended Access Systems Failure Permanent Access Systems Roof Anchor Systems Failure Lifeline Systems Failure Suspended Platform Failure Construction Safety Failure Building Maintenance Accident Construction Defect Analysis Construction Dispute Support Design vs Installation Discrepancies

System Performance Failure Infrastructure Access System Failures Access System Commissioning Issues Installation vs Design Intent Conflict Contractor Responsibility Analysis OEM Responsibility Analysis OSHA Compliance Review ANSI Standards / IWCA Standards Failure Analysis Construction Systems Mechanical Building Systems Lifecycle System Analysis Commissioning Review Maintenance Conditions

View Rauch Safety and Engineering's Consulting Profile.

Expert Background: Dr. Thomas L. Read is the Principal and CEO at A. Read Consulting, LLC. He received his PhD. from Stanford University in 1972 and has over 25 years of manufacturing experience in electronics, metallurgy, factory safety, failure analysis, glass fracture, glass failure and bottle failure. As a member of the electronics industry, he has earned process patents and has an extensive background in manufacturing techniques. In parallel, Dr. Read has spent over twenty five years as a consultant to attorneys and engineers. He has given more than 100 depositions and has appeared in court numerous times. Company Profile: Read Consulting, LLC is a full service laboratory providing services in the following areas:

• Failure Analysis; Factory Safety and Personal Injury (including machine guards and manufacturing safety)
• Glass Failure Analysis - Glass Fracture, Glass Failures and Bottle Failure
• Metal and Ceramic Failure
• Grinding Wheel Failures
• Intellectual Property and Patent Disputes
• Product Liability and Product Quality
• Manufacturing Disagreements (such as Intellectual Property, Failed equipment and Contract Disputes)
• Reverse Engineering

Since 1988, Real-World Forensic Engineering, LLC ("RWFE") has provided engineering services to industries and government labs, as well as litigation support to both plaintiff and defense attorneys practicing in many areas.

RWFE Areas of Expertise Include:

Components & Machinery Metallurgy & Corrosion Dynamics of Impact & Collisions Friction Analysis / Slips, Trips and Falls Intellectual Property & Patent Review Accident Reconstruction / Animation Computer Aided Design Education & Training

Electrocution & Switch Malfunction Grounding & Lightning Protection Lightning Impulse Testing Products and Premises Liability & Safety High-Voltage & Current Power Systems Bridge Design and Safety Fire & Explosion Cause and Origin And Much More...

At RWFE, we proudly distinguish ourselves by our Four C's:

CREDENTIALS. COMPETENCE. CREDIBILITY. COMMUNICATION.

Credentials:	B.S., M.S., M.Eng., M.B.A., J.D., and Ph.D. Degrees Licensed Professional Engineers in Mechanical, Electrical, and Civil Engineering Tenured University Professors and Professionals NAFI Certified Fire and Explosion Investigators (CFEI) Licensed Master Electricians
Competence:	Over 80 Combined Years of Experience in Engineering R&D, Industry, Academia, Consulting, and Expert Witness Litigation Support Over 120 Combined Deposition and Court Testimonies
Credibility:	Internationally Recognized in Our Areas of Expertise More Than $19 Million in Peer-reviewed and Funded Research Grants Over 200 Combined Scientific Publications and Journal Articles
Communication:	Over 20 Different Undergraduate and Graduate-level University Courses Over 30 Invited Short Courses, Talks, and Lectures

Design Evaluation – Accident Investigation – Intellectual Property - Failure Analysis – Fire Cause & Origin – Component Testing - Computer Aided Drafting – Accident Animation - Expert Witness & Litigation Support

www.ExpertEngineering.com

Richard Fincher is a consulting and testifying expert witness with over 40 years of Engineering, Semiconductor Manufacturing, Software, Industrial Automation, and executive leadership experience. He provides expert witness and litigation consulting services in U.S. federal and state courts, international arbitration, the U.S. International Trade Commission, and international proceedings.

 Litigation Support - Mr. Fincher has prepared expert, rebuttal, and technical reports and has provided deposition and trial testimony. His engagements have included multi-billion-dollar semiconductor disputes, semiconductor equipment valuation, software copyright and source-code analysis, patent invalidity and non-infringement, automotive electronics failure analysis, industrial machinery disputes, immersive simulation systems, and manufacturing technology matters.

His technical work has included source-code review under stipulated protective orders, establishment of specialized PLC and electronics laboratories for independent testing, semiconductor manufacturing and equipment-market analysis, accelerated-life and specification testing, root-cause analysis, and evaluation of engineering, commercial, and industry-practice issues.

Areas of Expertise:

Semiconductor Manufacturing and Economics Semiconductor Equipment Valuation and Secondary Markets ASIC Cost & Manufacturing Economics Yield, Capacity, and Utilization Analysis Software IP and Source Code Copyright and Trade Secret Disputes

Patent Litigation Embedded Systems Industrial Automation and Process Control PLC Systems Product Reliability Electronic Failure Analysis

Background Experience - Mr. Fincher’s industry experience includes leadership roles as VP of Engineering, CTO, General Manager, and senior engineering manager in semiconductor, electronics, software, and manufacturing organizations. He has led engineering and technology operations across the U.S., Europe, China, India, and Australia.

He holds an MBA from SMU Cox School of Business, an MS in Computer Science from SMU Lyle School of Engineering, and a BS in Computer Science from the University of Texas at Dallas. He is a PMP – Project Management Professional and a Lean Six Sigma Master Black Belt.

Consultants. Experts. Innovators.™

Operating from more than 110+ offices around the globe, we provide services to corporations, insurance companies, law firms, and government agencies.

Rimkus experts specialize in forensic consulting and construction dispute resolution in the hospitality, retail, and restaurant; industrial; marine; oil and gas; power and renewable energy; transportation; and pharmaceuticals industries.

Rimkus experts solve complex challenges wherever in the world they occur. We are dedicated to serving our clients so they can achieve timely resolution of accidents, claims, and legal disputes.

Our highly diversified, global team of engineers, scientists, architects, and technical specialists systematically evaluates all available evidence, applies scientific principles, specialized knowledge and, when appropriate, utilizes the latest analytical technologies to arrive at scientifically sound opinions and solutions for our clients.

Rimkus Global Services Overview

OUR FORENSIC SERVICES EXPERTISE

Architecture Biomedical Engineering Building Consulting Building Surveying Civil and Structural Engineering Construction Claims and Disputes Digital Forensics Environmental Health Science Fire and Explosion Science Geotechnical Engineering Human Factors

Industrial and Renewable Energy Legal Nurse Consulting Marine Forensics Materials Science Engineering Mechanical and Electrical Engineering Forensic Meteorology Premises Liability and Security Property Loss Consulting Toxicology and Food Safety Transportation Visual Media and Technology Services

View our full suite of Forensic Expert Services

GLOBAL OFFICES

Rimkus operates from 110+ offices worldwide, with headquarters in the following cities.

Australia Grosvenor Place, Level 31 225 George Street Sydney NSW 2000 Phone: +61 2 9290 1495 Email: APEnquiries@rimkus.com

Malaysia Menara Citibank Suite 20.04 Level 20, 165 Jalan Ampang 50450 Kuala Lumpur Phone: +60 3 9212 1204 Email: APEnquiries@rimkus.com

New Zealand Level 2, 1 Broadway Newmarket Auckland 1023 Phone: +64 9 5201929 Email: APEnquiries@rimkus.com

Singapore  138 Market Street Level 5, CapitaGreen 048946 Phone: +65 6016 6057 Email: APEnquiries@rimkus.com

United Kingdom 5th Floor 40 Lime Street London EC3M 7AW Phone: +44 12 5767 6107 Email: EurEnquiries@rimkus.com

United States 12140 Wickchester Ln Ste 300 Houston Texas Phone: +1 800 580 3228 Email: Expert@rimkus.com

View a full list of Rimkus Office Locations.

View Rimkus Quantum and Delay Expert Services Profile.
View Rimkus Life Sciences Expert Services Profile.

Christopher M. Daft, PhD, is an award winning, Oxford Educated scientist whose areas of expertise include medical imaging, artificial intelligence, semiconductors, medical devices, sensors, MEMS, signal processing, and image processing. He holds 23 United States Patents with 20 applications pending, Dr. Daft has diverse industry experience including multi-nationals such as GE, Medtronic, Fujifilm, Samsung, and Siemens as well as several start-ups. 

He has testified at trial 5 times and been deposed 15 times.

Dr. Daft has been an Institute of Electrical and Electronic Engineers (IEEE) Senior Member since 2004. He has three years of experience teaching electrical and computer engineering at the University of Illinois. 

Dr. Daft holds a BA and MA in Physics from Oxford University as well as Doctorate from Oxford in Materials Science.

Litigation Support - Dr. Daft provides litigation support in the areas of Intellectual Property and Medical Devices including Imaging, particularly Medical, Patents, and more. His experience includes a variety of cases in the areas of wearable electronics, imaging systems, and surgical technology. Dr. Daft has extensive deposition and trial testimony experience.

Areas of Expertise:

Design Engineering Electrical Engineering Electromagnetic Engineering Microelectronics Medical Imaging Electronics Semiconductors

Medical Devices Sensors Software Engineering MEMS Signal Processing Image Processing Physics

View Dr. Christopher Daft's Consulting Profile.

Gary D. Fletcher, PhD,  is the Founder and Principal Consultant at RnDDx Solutions LLC, a consulting firm founded in 2015, focused on Industrial Mechanical Engineering and Biomedical Engineering and Research and Product Development.  In his 30 years of experience, he has been co-inventor on 23 patents for devices and methods in blood collection and processing.

Litigation Support - Dr. Fletcher has subject matter expertise in Medical Device Mechanical Engineering and subject matter expertise in Medical Devices for blood and specimen collection and sample processing for in vitro diagnostics, point of care diagnostics, and therapeutics, including glucose monitoring. He serves as an expert witness in patent infringement cases involving medical device and diagnostic biomedical engineering, blood collection, separation, fluidic preparation, glucose monitoring, and cell therapy preparation devices.

Dr. Fletcher offers patent litigation services to law firms and lawyers supporting medical device and diagnostic industry clients, who need physical science and mechanical and biomedical engineering expertise for District Court, PTAB, and ITC patent cases. As an industry consultant, his ideal clients are R&D, product development, and innovation leaders in startup, emerging, and established medical device and diagnostic companies, who face product development and competitive challenges.

Areas of Expertise:

Mechanical Engineering Biomedical Engineering Medical Devices Product Development Clinical Diagnostics Blood Collection Blood  / Cell Separation Needles / Lancets Biospecimens Point of Care Testing Microfluidics

X-Ray Spectroscopy Cell Therapy Intellectual Property / Patent Infringement Microscopy Physics Biomedical Sensing Optics Imaging Mathematics Glucose Monitors Lasers

Dr. Fletcher is an entrepreneurial executive with expanding R&D roles in business, technology, and new product development leadership and execution, building and guiding teams in both Fortune 500 and startup companies. With a PhD in physics from Yale, he has a proven record of leadership in creating innovative new businesses and products in healthcare, medical devices, diagnostics, life, materials, and optical sciences.

Paul E. Rosenfeld, M.S., Ph.D., is the Founder and Principal Scientist of RoseyFields LLC and a nationally recognized forensic environmental scientist and plaintiff expert witness. Over 25 years, his work has spanned complex toxic-tort and class-action litigation — including MTBE, PFOA/PFAS, asbestos, FELA railroad exposure, air-dispersion modeling, epidemiology, toxicology, industrial contamination, and pesticide exposure matters — with an aggregate case value of approximately $14 billion, and he has been deposed approximately 150 times in 31 states.

Litigation Support

Dr. Rosenfeld's opinions are based on established scientific methodologies, quantitative exposure models, peer-reviewed scientific literature, published technical methods, and reproducible calculations that can be independently evaluated and tested, providing a rigorous scientific foundation for expert opinions under Daubert and related standards for the admissibility of scientific evidence. He has authored and contributed to books and technical publications concerning environmental contamination, exposure assessment, and risk evaluation and has applied these scientific methods in expert reports, litigation, depositions, regulatory proceedings, and trial testimony.

Methodologies & Scientific Approach

Dr. Rosenfeld's air dispersion modeling work applies EPA-approved and peer-reviewed models, including AERMOD, CALPUFF, and ALOHA, to reconstruct historical emissions, source attribution, and community-level exposure pathways. His exposure and dose reconstruction methods integrate environmental sampling data, regulatory exposure factors, and published toxicological and epidemiological literature to quantify human exposure to chemicals including benzene, PFAS/PFOA, TCE, hexavalent chromium, and crystalline silica, among others. Each methodology is applied transparently, allowing the underlying calculations, data inputs, and modeling assumptions to support general cuasation opinions. 

Publications & Court Qualifications

Dr. Rosenfeld has authored six books and dozens of peer-reviewed publications on environmental contamination and risk assessment. He has been qualified as an expert under Daubert and analogous standards in federal and state courts nationwide reflecting consistent application of scientifically defensible methodologies under prevailing standards for expert testimony admissibility.

Areas of Expertise:

Quantitative Exposure Assessment Environmental Fate and Transport Air Modeling & Mapping & Clas Dose Reconstruction Quantitative Risk Assessment General Causation PCBs, Schools & Building Asbestos and talc

PFAS / PFOA  Silica / Artificial Stone / Engineered Hazardous Chemicals / Environmental Contaminants Hazardous Air Pollutants Soil Toxins PCBs and PFAS in Dust Water Pollutants Lead, Mercury, Arsenic

Dr. Shakir Shatnawi, PhD, PE, is a nationally and internationally recognized expert in the Transportation Engineering industry. Shakir has a Ph.D. in Transportation Engineering. He has over 30 years of practical and extensive engineering and transportation expertise covering industry and public agencies including FHWA and the California Department of Transportation (Caltrans). 

Shakir is currently the president of Shatec Engineering Consultants. He taught highway engineering, traffic engineering and transportation engineering and pavement design at California State University. Dr. Shatnawi served as a principal investigator on multi-million dollar transportation projects. He held various positions at Caltrans including a Senior Transportation Engineer, a Supervising Transportation Engineer and a Division Chief.

 Dr. Shatnawi's education and experience demonstrates a wealth of engineering knowledge encompassing highway design, traffic engineering, pavement design, geotechnical engineering, materials and construction . As a recipient of many acknowledgements from the government, Dr. Shatnawi has an impeccable reputation within the industry for his significant professional contributions. As an expert orator, he frequently shares his knowledge at major conferences around the world. Dr. Shatnawi provides expert witness services in the following areas:

Traffic Engineering Highway Design Standards Highway Specifications / Guidelines Public Agency Policies / Practices Pavement Design / Materials Construction defects Highway Geometric Design Drainage Asphalt Concrete Highway Repairs / Maintenance

Construction Quality Control / Quality Assurance Construction Claims Surface Conditions - Friction, Skid Resistance Road Defects Traffic Safety Highway Safety Traffic Control Devices / MUTCD Sight Distance Requirements Roadside Hazards ADA Requirements Code Violations

View Dr. Shatnawi's Consulting Profile.

William C. Stein, Jr., PE, CCM, has more than 45 years of Roadway / Heavy Highway Construction and Materials Engineering experience. He has a rich and varied work history that includes construction materials engineering for highways and bridges, industrial plants, high rise offices, and power plants. He has worked for private owners and general contractors as well as the Department of Transportation.

Litigation Support - Mr. Stein Offers consulting and expert services for attorneys on issues regarding road, street, highway, temporary traffic control, runway, and earthwork; asphalt, concrete, coatings and other construction materials; designs, plans, specifications, CPM scheduling (Primavera) and contract documents; right-of-way issues; and work zone safety. Licensed in Louisiana, Pennsylvania, and Texas, he performs contract performance forensic investigations and provides consulting, expert reports, rebuttals, and testimony if required.

Areas of Expertise:

Highway Construction Roadway Construction Bridge Construction Highway Engineering Materials Engineering Construction Site Work

Traffic Safety Concrete / Cement Building Contractor Liability Construction Damages Scheduling Delay and Analysis Soil Analysis

Certifications:

• Certified Construction Manager (CCM)
• Certified Primavera Basic (CPM)
• Certified Primavera Advanced (CPM)
• Certified LADOTD Structural (bridge)
• Inspector/Technician Certified Troxler
• Humboldt Nuclear Moisture/ Density Operator
• Lead Abatement
• Certified Quality Compliance Surveillance in Fossil Power Plants, Organic & Inorganic Coatings Application and Inspection
• Certified Traffic Control Supervisor
• Certified Flagger Instructor

Mechanical Engineer - Turbomachinery Expert. Gas turbine engines, steam turbines, jet engines, compressors, pumps, expanders, generators, cogeneration, combustion equipment, diesel engines, and reciprocating compressors. 

Failure analysis, stress analysis, mechanical design, design analysis, troubleshooting, performance analysis, durability assessment. Access to metallurgical laboratory. Experienced Expert witness. 

Please see our Service List at https://sbkushnick.com/servicelist.pdf for a concise description.

Thomas W. Caldwell, PE, has over 40 years of experience in Materials Research and Development, Process and Product Development, and Manufacturing Operations in the Precision Cast and Machined Products industry.

Mr. Caldwell has designed and manufactured components for consumer and industrial products, including safety-critical applications such as aircraft landing gear brakes, seat belt lockup devices, windshield wiper, and window lift motor systems. He has experience creating and guiding technology development and manufacturing partnerships in Europe and Asia, licensing and selling intellectual property and creating supply chains in China.

Mr. Caldwell has lectured in the USA, Germany, Switzerland, and India on manufacturing premium quality metal products and manufacturing processes, and was a technical paper peer reviewer for 20 years for the Society of Automotive Engineers. A United States patent holder, he has published peer reviewed research in electrochemistry and materials processing, and has written and spoken numerous times on the subject of Materials Selection.

Litigation Support - Thomas W. Caldwell, PE, is a testifying and consulting expert for both plaintiff and defense counsel. His cases involve product failure for ferrous and non-ferrous alloy products such as hand tools, recreational and exercise equipment, fire fighting apparatus, rotating industrial machinery, construction hardware, piping, and lighting fixtures. Mr. Caldwell utilizes destructive and non-destructive methods for insuring product integrity.

Areas of Expertise:

Design Engineering Materials Failure Analysis Materials Engineering Mechanical Engineering Metallurgy Power Tools Products Liability Design Defects

Manufacturing Defects Fitness for Use Equipment Operation and Maintenance Accident Reconstruction Material Selection Manufacturing Process Design and Scale Up Safety Component Product Quality Control Safety Component Quality Systems Management

View Thomas A. Caldwell's Consulting Profile.

Bransford Pickett, PE, DFE, BSc, MScBA, has over 25 years of experience as a Mechanical Engineer. SEFS expertise includes design and review of material handling equipment, material handling management, and ship board systems. SEFS offers litigation support services for Accident Investigation and Reconstruction covering failure analysis, process simulation, regulatory compliance, equipment reliability, and personal injury / safety. His materials handling and engineering services are offered to attorneys, insurance and end user companies nationally and internationally.

Mr. Pickett is a member on the American Society of Mechanical Engineers B30 committee on Safety Codes and Standards for cranes and rigging as well as a member of several subcommittees. He is also a member of American Society of Mechanical Engineers P30 Committee- Planning for the Use of Cranes, Derricks, Hoists, Cableways and Lifting Accessories. ASME BTH Standards Committee.

Mr. Pickett is a Professional Engineer, and holds a BSE from the University of Michigan, Ann Arbor, and a MScBA in Finance from San Diego State University, as well as a board certified Diplomate Forensic Engineer. He has qualified as an expert witness in the State of New York Supreme Court and the State of California Supreme Court.

Accident Investigation:

• Man baskets, Forklifts, Scissors Lifts, Aerial Lifts, Rigging Gear, Hydraulic Jacks, and Hydraulic / pneumatic Lift Systems, Automotive Lift Systems, Conveyors, Pallet and Packages Conveyors, Pneumatic Systems, Machine tools, Boats, Barges, and Elevators
• Tower, Mobile, Bridge, Truck, Portal, Container, Jib and Floating Barge Cranes, and Derricks
• Operator training compliance to National Commission for the Certification of Crane Operators, NCCCO, requirements for tower crane, mobile crane, overhead crane, articulating crane operator training and certification, signal person, and rigger certification
• Compliance covers applicable national and international standards that include the ABS, ASTM, ASM, ASME, ANSI, WSTDA, ALI, etc. and DIN, EN, FEM to list a few. National regulations include state and federal OSHA requirements as well as DOE, military specifications and standards

View Bransford Pickett's Consulting Profile.

Dr. Tal Lavian holds a Ph.D. in Computer Science from UC Berkeley, specializing in network communications. 35+ years as a scientist, educator, and technologist; 20 years researching, studying, and lecturing at UC Berkeley; Industry Fellow and Lecturer at UC Berkeley's College of Engineering.   90+ cases · 60+ depositions · 8+ trial testimonies · 100+ patents supported in IP litigation · 120+ patents as inventor · 60+ pro-se prosecuted · 25+ peer-reviewed publications 

Areas of Expertise:

Telecommunications  - Computer Networks - Network Communications - Internet Protocols (TCP/IP) - VoIP - Streaming Media - Mobile Wireless: Wi-Fi (IEEE 802.11), Bluetooth (IEEE 802.15), cellular, routing and switching (MPLS, BGP, OSPF), network security, streaming media, and network management (SNMP) expert witness. 

• Network Communications: TCP/IP suite, TCP, UDP, IP, Ethernet (IEEE 802.3), SNMP, packet switching, network architecture
• Mobile Wireless: Wi-Fi (IEEE 802.11), Bluetooth (IEEE 802.11), Wireless LAN (WLAN), cellular systems, SMS, mobile devices
• Internet/Cloud: HTTP, web applications, cloud computing, distributed computing
• Routing/Switching: LAN, WAN, VPN, VLAN, LAG, ARP, DHCP, DNS, quality of service (QoS).
• Network Protocols: IPv4, IPv6, RIP, BGP, MPLS, OSPF, multicast
• VoIP/Streaming Media: SIP, RTP, H.323, PSTN, circuit switching, SS7, WebRTC, video/audio conferencing.
• Network Security: Firewalls, VPN, IPSec, SSL/TLS, deep packet inspection, L4-7 switching, NAC
• Network Management: NMS, SNMP, device management, OSS, alarm systems
• Communication Standards: IEEE, IETF, ITU, ISO

Case Experience:

Dr. Lavian has served as an expert in over 90 patent cases involving more than 100 patents. He has provided reports and testimony in U.S. federal district courts, state courts, the USPTO PTAB (IPR, CBM, PGR, ex parte reexamination, interference), the ITC, and international courts. Cases have involved Apple, Google, Facebook (Meta), Microsoft, Amazon, Tesla, Cisco, Juniper Networks, Arista Networks, Ericsson, T-Mobile, Samsung, LinkedIn, Huawei, Netflix, Broadcom, SAP, and others. 

While at UC Berkeley, Dr. Lavian conducted research projects in data centers (RAD Labs), network communication service architecture (SAHARA), and wireless systems (ICEBERG); he also served as an industry fellow and lecturer at the Sutardja Center for Entrepreneurship and Technology (SCET) and as a scientific liaison between Nortel Research Lab and UC Berkeley. Dr. Lavian was also part of UC Berkeley's SkyDeck start-ups, where he worked on technology research and implementation. 

Credentials:

• Inventor of over 120 U.S. patents; over 60 prosecuted pro se
• 20 years UC Berkeley - 10+ years Nortel Research. 
• Over 25 peer-reviewed publications in IEEE and ACM
• Principal Investigator on three DARPA projects
• IEEE Senior Member
• Nortel Networks Principal Scientist

About Dr. Lavian

Dr. Lavian's Website

Dr. Lavian's Expertise

Cassandra K. Moody, MS, PE, the President and Principal Engineer of Time For Change, LLC., is a professional engineer with nearly 15 years of Pipeline Engineering and Operations experience encompassing Integrity Management Program (IMP) responsibilities.

Litigation Support - As a proficient expert in the midstream pipeline industry, Mrs. Moody has represented both plaintiffs and defendants on a variety of cases, both by testimony and through expert opinion reports. In-the-ditch pipeline operator expertise sets her apart from other desktop “experts.” Mrs. Moody’s retained engagements as an independent engineering expert have resulted in favorable resolutions for 100% of her clients to date.  Mrs. Moody is an effective communicator who excels at presenting complex information simply, both written and verbally.

Subject Matter Expertise:

Pipeline Integrity Management Midstream Pipeline Design Midstream Pipeline Operations Pipeline Project Management Pipeline Safety Management Systems

Risk and Threat Assessment Continuous Improvement Change Management Principles Regulatory Compliance Failure Analysis

Background Experience - Prior to establishing her own consultancy firm, she served in various regional operations engineering capacities, leading people and managing projects for a midsize North American pipeline operator as an Operations Engineer. Mrs. Moody has performed practical operations analysis of new and existing pipeline systems and facilities, of both natural gas and hazardous liquid product types, from operability optimizations, cost consciousness, and regulatory compliance perspectives throughout her career. She offers innovative solutions to achieve safe and efficient operations while communicating visionary changes in processes and procedures through training and encouragement across all levels of organizations to result in lasting, favorable change.

Mrs. Moody's company maintains national and local certifications as a Women’s Owned Small Business (WOSB), Women’s Business Enterprise (WBE), and is recognized as a Historically Underutilized Business (HUB) in the state of Texas. She was a founding leadership team member of Young Pipeline Professionals, USA (YPP USA) and is active with the Society of Women Engineers – Houston Section (SWE) where she enjoys encouraging the next generation through activities such as Introduce a Girl to Engineering Day outreach events. 

Mrs. Moody attributes her ability to support a wide variety of projects to her broad education foundation where she earned undergraduate Bachelor of Science degrees in Biochemistry and Genetics from Texas A&M University and a Master of Science in Environmental Engineering through the University of Houston. She is registered with the Texas Board of Professional Engineers and Land Surveyors as a Mechanical Engineer.